Brakes: Pads, Discs and Fluid, and the Warnings They Give
Brakes are designed to wear out, and they tell you long before they stop working. Learning the sounds and the feel is the cheapest safety upgrade there is.
What happens when you brake
Braking turns movement into heat. A disc brake does it by squeezing a pair of pads against a disc that turns with the wheel. A drum brake, still common on the rear of small cars and on the rear wheel of many scooters, presses shoes outwards against the inside of a drum. Either way, friction material is given up on purpose, a little at a time, and the heat goes into the air. That is why brakes are a maintenance item rather than a fitted part: wearing out is the job.
The parts that wear
- Pads and shoes. The friction material itself. It thins steadily and unevenly, and the inner and outer pad on the same wheel often wear at different rates.
- Discs and drums. They wear too, more slowly, and can end up grooved, lipped at the edge or unevenly thick.
- Fluid. A service item with its own interval, for the reason set out below.
- Hoses, seals and pistons. Rubber ages whether the vehicle is used or not.
- Sliding pins and cable brakes. These need the grease or adjustment the manual specifies, or the brake drags and wears on one side.
What worn brakes feel and sound like
- A hard scraping or grinding noise, which usually means the friction material has gone and metal is on metal. Stop using the vehicle and get it looked at.
- A light squeal in the first stops of a damp morning, which is often normal; a squeal that stays all day, which is not.
- A pedal or lever that travels further than it used to, or feels soft and spongy.
- Pulling to one side under braking, which points at one brake working harder than the other.
- Pulsing through the pedal or the handlebars, which usually comes from a disc that is no longer running true.
- A warning light, or a brake fluid level that keeps dropping. Falling fluid in a sealed system means it is going somewhere.
Brake fluid is a service item too
Brake fluid carries the force from your foot or hand to the brakes themselves, and it works because liquid does not compress. Most types are hygroscopic, meaning they absorb moisture from the air over time, and water in the fluid lowers its boiling point and corrodes the system from the inside. That is why the manual gives a replacement interval measured mainly in time rather than distance, and why it applies even to a vehicle that has barely moved.
Use only the fluid type the manual names, from a container that was sealed, and do not mix types. It strips paint on contact, so keep it off bodywork. Topping up without finding out why the level fell is not a repair.
Heat, fade and long descents
Brakes that get very hot lose some of their effect, a condition called brake fade. It shows up where brakes are used continuously: a long mountain descent, a heavily loaded car, a scooter ridden hard downhill. The answer is to let the engine do part of the work by holding a lower gear, and to brake firmly for short periods and then let the brakes cool, rather than dragging them all the way down. On two wheels, use both brakes together as your manual advises; the front does most of the stopping, but the rear still matters.
Habits that make brakes last
- Look at your fluid level and the thickness of the outer pad whenever you check the oil.
- Leave enough following distance that most of your slowing is done by lifting off, not by braking.
- Do not rest a foot or finger on the brake while driving or riding.
- After riding or driving through deep water, dry the brakes with a few gentle stops at low speed.
- If the vehicle stands for weeks, expect surface rust on the discs; it normally polishes off in the first few stops.
What to leave to a workshop
Inspecting brakes and keeping an eye on the fluid is reasonable for an owner. Replacing pads, machining or renewing discs, bleeding the system and tracing a leak are not beginner jobs, and a mistake here does not give you a second chance. A garage can also measure what you cannot see: the remaining thickness of the pads and discs against the manufacturer's limits, and the condition of the fluid.
Brakes are a safety system. If anything about them has changed and you do not know why, treat the vehicle as unroadworthy until it has been checked.
Checked 2026-11-19